Front left hand brake pipe linking caliper to rigid pipe under fuel tank

Original type rubber brakeline with chunky galvanized ends

 This part is available by special order, request a quote

14658851-z 14658851 GU14658851 14 65 88 51
 1465 8851 1465.8851 14.65.88.51

Rear brakeline from splitter or proportioning valve to rear caliper fixed pipe. Also used as lower front right hand pipe to caliper fixed pipe on T3

Original type rubber brakeline with chunky galvanized ends

 This part is due back in stock soon, call 01484 841395 to reserve yours

17657550

Fixed rigid brake pipe linking front and rear of linked system, located under fuel tank

Original type rigid brake line

 This part is due back in stock soon, call 01484 841395 to reserve yours

17658750

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover

   This part is due back in stock soon, call 01484 841395 to reserve yours

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Flexible brake pipe from linked master cylinder to proporting valve or rear manifold

Original type rubber brake line with chunky ends

 This part is available by special order, request a quote

18658560

Brake pipe used for supplying front left hand caliper, screws directly into caliper

Original type rubber brakeline with chunky galvanized ends

 This part is available by special order, request a quote

17658860-z 17658860 GU17658860 17 65 88 60
 1765 8860 1765.8860 17.65.88.60

Brake pipe. Used to link rear master cylinder to splitter. Also used as pipe from front master cylinder on some models.

Original type rubber brakeline with chunky galvanized ends

 This part is available by special order, request a quote

 17658550 GU17658550 17 65 85 50
 1765 8550 1765.8550 17.65.85.50

Threaded linkage block used on brake or gear linkages (varies by model). Screws to M6 threaded rod

Wears over time, so we recommend replacing if your gear or brake linkage is sloppy

 This part is available by special order, request a quote

 18257551 GU18257551 18 25 75 51
 1825 7551 1825.7551 18.25.75.51

M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits in corrosion resistant grade 5 titanium as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap

 Availability varies on this part, check availability

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals and O ring to seal the two halves together

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)